How To Clean A Browning Bar Mark Ii Safari

Disassembly

NEVER ATTEMPT TO Accept YOUR BAR Apart FURTHER THAN EXPLAINED IN THIS MANUAL.

This is a specialized, finely fitted mechanism. You may permanently mar it by attempting to detach the inner mechanism assemblies. If further disassembly for senice or cleaning is required, have your gun to a Browning recommended Service Centre or a competent gunsmith, or transport it to our Arnold, Missouri Service Facility as explained under "Service or Repair".

one Be Sure THE Burglarize IS UNLOADED.

With the rifle in the ON SAFE position and pointed in a prophylactic down management, release the magazine floorplate to its open up position. Grasp the 60)lt operating handle and move it smartly to the rear, thereby extracting and

Figure 9

Pull action bar out of the receiver.

Figure ix

Pull action bar out of the receiver.

Effigy x

Figure 11___________

ejecting any live circular in the chamber. Remove all rounds from the magazine clip on the hinged floorplate. Always visually inspect the sleeping room to brand sure in that location are no rounds present. (Meet page vii for instructions on removing and unloading the magazine).

2 Remove forearm: Loosen and remove the fore-ami hinge eyelet with a small wrench by turning in a counter-clockwise direction. Intendance should l>eastward taken to prevent scratching the fore

arm. Grasp the forward end of the forearm and pull away from the butt carefully until firm resistance is felt. Then slide the foreami forward and off. (The foreami must be pulled abroad from the butt so that the forearm will clear the bottom of the gas cylinder equally the forearm is moved forward.) Note: The foreami cannot exist removed unless the bolt is locked open. In social club to lock the bolt open up, the magazine clip must be on the hinged floorplate.

3 Remove action confined: Close the bolt by depressing the liolt release lever. To remove the left activeness bar pull the forrad end away from its slot on the inertia slice. Then lower and pull the activeness bar forwards and out of the receiver. (See Effigy 9) Remove the right action bar by first releasing the lx>lt release lever spring from the Ixilt release lever and removing the spring from the receiver. (See Figure ten) Remove the lx)lt release lever pin and pull the commodities release lever forward and out of the receiver. (See Figure 11) You tin can so pull the frontward terminate of the activeness bar away from the inertia slice and lower and pull the activity bar out of the receiver.

four Remove gas q'linder spiral cap from the forward end of the gas cylinder: Turn in a counter-clockwise direction. (See Figure 12) Use a 11/xvi" wrench for this functioning.

5 Remove the gas piston: The inertia block should be pulled back toward the receiver until rear face of the gas piston can exist pushed for-

Effigy xiv

Remove activity spring, activeness leap guide and inertia block.

Figure fourteen

Remove activity spring, action jump guide and inertia block.

Supervene upon action spring, action bound guide and inertia block into recess in receiver.

action spring, action spring guide, and inertia block. (See Figure 14)

Hie gas cylinder can now be examined for accumulations of residue. Residues in the gas cylinder and on the gas piston should be thoroughly removed with a skilful quality pulverisation solvent or bore cleaner. If residues are heavy, they tin be removed past scrubbing the gas cylinder with a 20 approximate shotgun bronze wire bore castor and a good solvent.

ward out of the gas cylinder with a pocket-sized drive punch. (See Effigy 13) Notation: An extremely dirty gas cylinder and gas piston may require forcefully moving the gas piston frontwards with a hammer and drive punch, and extreme care must be used to avoid scoring parts. If the gas piston will not move with moderate forcefulness, piace a couple of drops of nitro-solvent effectually the gas piston, expect near 15 minutes, then endeavor to button the piston out with the drive punch. If the piston still volition not movement, put more nitrosolvent on the piston and allow it to gear up overnight before attempting to remove the piston.

6 Remove the inertia block, activeness spring, and action spring guide: Tightly grip by manus the rear portion of the activity and action spring guide and pull forward toward gas cylinder until the action spring guide is articulate of its recess in the receiver. The rear end of the activity spring guide can and so Ix? moved to one side of the receiver and then rearward to remove the

Note: the gas cylinder spiral located on the gas cylinder is set at the manufactory. do non change the setting on the gas cylinder screw. Any changes to the gas cylinder screw may adversely affect the accuracy and operation of your rifle.

The gas piston, gas cylinder, and other parts covered by the forearm should be wiped with a very lightly oiled cloth afterwards cleaning. The gas cylinder interior and the gas piston should not be oiled beyond this.

Was this commodity helpful?

Source: https://www.bevfitchett.us/browning-bar-mark-2-safari/disassembly-1.html

Posted by: johnsonjointlaim.blogspot.com

Share this post